AUTOLOGIC ON MERCEDES

Autologic discusses some faults they commonly see on Mercedes 212, 207, 204 and 218 from production period 12/2011 to 03/2012

Autologic reports symptoms can vary depending on the model range of the vehicle.
The warning lights could come on, some models might have various broken functions including the wiper washers, and for some models it can even result in the engine not being able to start, or not allowing you to select a gear.
Autologic states it has found that re-cycling the ignition may fix the issue temporarily.

Fixing the fault:
Autologic states carrying out a full vehicle scan will show most control units with numerous CAN communication faults.
It says a typical fault read will give CAN faults in:
• ESP
• Engine
• Transmission
• EIS (ignition switch)
• Rear SAM
• Xenon Headlights (if fitted)
• SRS
• Multifunction camera
• PARKTRONIC
All reporting CAN issues will be stored faults, says Autologic, stating that the common theme across all models are the codes in the rear SAM and SRS – this will give you a diagnosis point to the problem, it says.
In the rear SAM, Autologic explains you will have a few rear light codes, and the following:
• A19600 (B219600) [Stored] The power supply of circuit 30g is < 7.5 V
• A19700 (B219700) [Stored] The power supply of circuit 30g is < 8.5 V
• A19116 (B219116) [Stored] The power supply of circuit 30g is outside the valid range. The limit value for electrical voltage has not been attained
• A14B72 (B214B72) [Stored] The output for switch ‘Quiescent current ON’ has a malfunction. The actuator does not close
These codes are important as it will indicate the premature closing of the 30G relay in the f32 fuse box. The other sign of this being the cause are the codes in SRS – SRS: Airbag. Part no. 212 901 42 04. There are three faults:
• A10F (B210F) [Stored] Event: Input ‘Circuit 30’ has a malfunction
• 9C1A (B1C1A) [Stored] NECK-PRO head restraint ‘Front passenger’ has an open circuit
• 9C14 (B1C14) [Stored] NECK-PRO head restraint ‘Driver’ has an open circuit
In 100 percent of cases, says Autologic, these codes will be stored in the SRS module if the 30G feed is shut off prematurely.

Cause of the problem
Autologic explains the cause of the problem is a defective no-load current relay in the engine compartment pre-fuse box F32 (this is the jump point fuse box under the bonnet)

What is 30G?
30G is a 12Volt permanent live circuit which is shut down after six hours after the vehicle is locked. The result of which means that 60 percent of control units receive a hard reset (power off and then on again at vehicle restart); this has the effect of less vehicle problems.
1. The rear SAM checks after 75 minutes and will find a drain of >50mA
2. It will then give a five-minute warning to the other control units to shut down
3. After the other control units have shut down, it will then shut circuit 30G by triggering the shut off a control relay in F32 (front electrical pre-fuse box) without waiting the six hours
a. If the voltages/quiescent current is within spec, the rear SAM will go back to sleep
b. The system will always try to ensure the vehicle is able to start
c. The battery sensor has a diagnostic facility to help diagnosis of current drain faults
It’s important to disconnect the battery to replace the f32 fuse box. Note: Remove the battery sensor in the correct way or this will cause issues after you’ve finished.
• Procedure for disconnecting the battery (battery sensor): unplug the electrical plug from the sensor (B95 red and blue wires); unbolt the negative terminal.
• Procedure for connecting the battery sensor: connect the negative terminal (terminal clamp bolt torque is 6nm); reconnect the electrical plug to the battery sensor clear codes; (on vehicles with option code 510 or 523 a clock reset is required).
• Electrical connection for B95
Red +30 from battery positive
Blue/white LIN wire to rear SAM
When disconnecting the battery, using the wrong sequence can cause arcing and contact bounce. This will cause a LIN communication error, putting the battery sensor (B95) into a passive state and at this point it will stop sending information to rear SAM. ECO start stop will also stop working. Note: no steps are required for initial start-up of B95 battery control module
Once the battery is correctly disconnected, the f32 fuse box can be replaced with a new part from Mercedes-Benz (modified). The old f32 has a design fault and will shut off without the command from rear SAM.
The battery will then be put back on line after the replacement. Then clear codes as necessary and road test the vehicle on job completion.

For more from Autologic, call 03 8561 7600 or visit www.autologic.com